Generic Sensor API

1. Introduction

Increasingly, sensor data is used in application development to enable new use cases such as geolocation, counting steps or head-tracking. This is especially true on mobile devices where new sensors are added regularly.

Exposing sensor data to the Web has so far been both slow-paced and ad-hoc. Few sensors are already exposed to the Web. When they are, it is often in ways that limit their possible use cases (for example by exposing abstractions that are too high-level and which don’t perform well enough). APIs also vary greatly from one sensor to the next which increases the cognitive burden of Web application developers and slows development.

The goal of the Generic Sensor API is to promote consistency across sensor APIs, enable advanced use cases thanks to performant low-level APIs, and increase the pace at which new sensors can be exposed to the Web by simplifying the specification and implementation processes.

A comprehensive list of concrete sensors that are based on Generic Sensor API, applicable use cases, and code examples can be found in [GENERIC-SENSOR-USECASES] and [MOTION-SENSORS] explainer documents.

2. Scope

This section is non-normative .

The scope of this specification is currently limited to specifying primitives which enable exposing data from device sensors .

Exposing remote sensors or sensors found on personal area networks (e.g. Bluetooth) is out of scope. As work in these areas mature, it is possible that common, lower-level primitives be found, in which case this specification will be updated accordingly. This should have little to no effects on implementations, however.

This specification also does not currently expose a sensor discovery API. This is because the limited number of sensors currently available to user agents does not warrant such an API. Using feature detection, such as described in § 3 A note on Feature Detection of Hardware Features , is good enough for now. A subsequent version of this specification might specify such an API, and the current API has been designed with this in mind.

3. A note on Feature Detection of Hardware Features

This section is non-normative.

Feature detection is an established Web development best practice. Resources on the topic are plentiful on and offline and the purpose of this section is not to discuss it further, but rather to put it in the context of detecting hardware-dependent features.

Consider the below feature detection examples:

if (typeof Gyroscope === "function") {
    // run in circles...
}
if ("ProximitySensor" in window) {
    // watch out!
}
if (window.AmbientLightSensor) {
    // go dark...
}
// etc.

All of these tell you something about the presence and possible characteristics of an API. They do not tell you anything, however, about whether that API is actually connected to a real hardware sensor, whether that sensor works, if its still connected, or even whether the user is going to allow you to access it. Note you can check the latter using the Permissions API [PERMISSIONS] .

In an ideal world, information about the underlying status would be available upfront. The problem with this is twofold. First, getting this information out of the hardware is costly, in both performance and battery time, and would sit in the critical path. Secondly, the status of the underlying hardware can evolve over time. The user can revoke permission, the connection to the sensor be severed, the operating system may decide to limit sensor usage below a certain battery threshold, etc.

Therefore, an effective strategy is to combine feature detection, which checks whether an API for the sought-after sensor actually exists, and defensive programming which includes:

1. checking for error thrown when instantiating a Sensor object,

2. listening to errors emitted by it,

3. handling all of the above graciously so that the user’s experience is enhanced by the possible usage of a sensor, not degraded by its absence.

let accelerometer = null;
try {
    accelerometer = new Accelerometer({ frequency: 10 });
    accelerometer.addEventListener('error', event => {
        // Handle runtime errors.
        if (event.error.name === 'NotAllowedError') {
            console.log('Permission to access sensor was denied.');
        } else if (event.error.name === 'NotReadableError' ) {
            console.log('Cannot connect to the sensor.');
        }
    });
    accelerometer.addEventListener('reading', () => reloadOnShake(accelerometer));
    accelerometer.start();
} catch (error) {
    // Handle construction errors.
    if (error.name === 'SecurityError') {
        console.log('Sensor construction was blocked by the Permissions Policy.');
    } else if (error.name === 'ReferenceError') {
        console.log('Sensor is not supported by the User Agent.');
    } else {
        throw error;
    }
}

4. Security and privacy considerations

Sensor readings are sensitive data and could become a subject of various attacks from malicious Web pages. Before discussing the mitigation strategies we briefly enumerate the main types of the sensor 's privacy and security threats. The [MOBILESENSORS] categorizes main threats into location tracking , eavesdropping , keystroke monitoring , device fingerprinting , and user identification . This categorization is a good fit for this specification.

The risk of successful attack can increase when sensors are used with each other, in combination with other functionality, or when used over time, specifically with the risk of correlation of data and user identification through fingerprinting. Web application developers using these JavaScript APIs should consider how this information might be correlated with other information and the privacy risks that might be created. The potential risks of collection of such data over a longer period of time should also be considered.

Variations in sensor readings as well as event firing rates offer the possibility of fingerprinting to identify users. User agents may reduce the risk by limiting event rates available to web application developers.

Minimizing the accuracy of a sensor’s readout generally decreases the risk of fingerprinting. User agents should not provide unnecessarily verbose readouts of sensors data. Each sensor type should be assessed individually.

If the same JavaScript code using the API can be used simultaneously in different window contexts on the same device it may be possible for that code to correlate the user across those two contexts, creating unanticipated tracking mechanisms.

User agents should consider providing the user an indication of when the sensor is used and allowing the user to disable it. Additionally, user agents may consider allowing the user to verify past and current sensor use patterns.

Web application developers that use sensors should perform a privacy impact assessment of their application taking all aspects of their application into consideration.

Ability to detect a full working set of sensors on a device can form an identifier and could be used for fingerprinting.

A combination of selected sensors can potentially be used to form an out of band communication channel between devices.

Sensors can potentially be used in cross-device linking and tracking of a user.

4.1. Types of privacy and security threats

This section is non-normative.

4.1.1. Location Tracking

Under this type of threat, the attacks use sensor readings to locate the device without using GPS or any other location sensors. For example, accelerometer data can be used to infer the location of smartphones by using statistical models to obtain estimated trajectory, then map matching algorithms can be used to obtain predicted location points (within a 200-m radius) [MOBILESENSORS] .

4.1.2. Eavesdropping

Recovering speech from gyroscope readings is an example of eavesdropping attack. See [GYROSPEECHRECOGNITION] .

4.1.3. Keystroke Monitoring

Many user inputs can be inferred from sensor readings , this includes a wide range of attacks on user PINs, passwords, and lock patterns (and even touch actions such as click, scroll, and zoom) using motion sensors. These attacks normally train a machine learning algorithm to discover such information about the users. See [STEALINGPINSVIASENSORS] .

4.1.4. Device Fingerprinting

Sensors can provide information that can uniquely identify the device using those sensors. Every concrete sensor model has minor manufacturing imperfections and differences that will be unique for this model. These manufacturing variations and imperfections can be used to fingerprint the device [ACCELPRINT] [MOBILESENSORS] .

4.1.5. User Identifying

Sensor readings can be used to identify the user, for example via inferring individual walking patterns from smartphone or wearable device motion sensors' data.

4.2. Mitigation Strategies

This section is non-normative.

This section gives a high-level presentation of some of the mitigation strategies specified in the normative sections of this specification.

4.2.1. Secure Context

Sensor readings are explicitly flagged by the Secure Contexts specification [POWERFUL-FEATURES] as a high-value target for network attackers. Thus all interfaces defined by this specification or extension specifications are only available within a secure context .

4.2.2. Permissions Policy

To avoid the privacy risk of sharing sensor readings with contexts unfamiliar to the user, sensor readings are only available for the documents which are allowed to use the policy-controlled features for the given sensor type . See [PERMISSIONS-POLICY] for more details.

4.2.3. Focused Area

Sensor readings are only available for active documents whose origin is same origin-domain with the currently focused area document.

This is done in order to mitigate the risk of a skimming attack against the browsing context containing an element which has gained focus , for example when the user carries out an in-game purchase using a third party payment service from within an iframe.

4.2.4. Visibility State

Sensor readings are only available for the active documents whose visibility state is "visible".

4.2.5. Permissions API

Access to sensor readings are controlled by the Permissions API [PERMISSIONS] .

Note: in specific cases such as [AMBIENT-LIGHT] , integration with the Permissions API is done indirectly -- illuminance readings are provided only when at least one local camera source is not muted or stopped . By definition, that implies the "camera" permission has been granted.

4.3. Mitigation strategies applied on a case by case basis

Each sensor type will need to be assessed individually, taking into account the use cases it enables and its particular threat profile. While some of the below mitigation strategies are effective for certain sensors, they might also hinder or altogether prevent certain use cases.

Note: These mitigation strategies can be applied constantly or temporarily, for example when the user is carrying out specific actions, when other APIs which are known to amplify the level of the threat are in use, etc.

4.3.1. Limit maximum sampling frequency

User agents may mitigate certain threats by limiting the maximum sampling frequency . What upper limit to choose depends on the sensor type , the kind of threats the user agent is trying to protect against, the expected resources of the attacker, etc.

Limiting the maximum sampling frequency prevents use cases which rely on low latency or high data density.

4.3.2. Stop the sensor altogether

This is obviously a last-resort solution, but it can be extremely effective if it’s temporal, for example to prevent password skimming attempts when the user is entering credentials on a different origin ( [rfc6454] ) or in a different application.

4.3.3. Limit number of delivered readings

An alternative to limiting the maximum sampling frequency is to limit the number of sensor readings delivered to Web application developer, regardless of what frequency the sensor is polled at. This allows use cases which have low latency requirement to increase sampling frequency without increasing the amount of data provided.

Discarding intermediary readings prevents certain use cases, such as those relying on certain kinds of filters.

4.3.4. Reduce accuracy

Reducing the accuracy of sensor readings or sensor reading timestamps might also help mitigate certain threats, thus user agents should not provide unnecessarily verbose readouts of sensors data.

Implementations of concrete sensors may define a threshold check algorithm so that new readings that do not differ enough from the latest readings are discarded.

Implementations of concrete sensors may define a reading quantization algorithm to reduce the accuracy of the sensor readings received from a device sensor .

Note: these two mitigation measures often complement each other. An implementation that only executes the threshold check algorithm might expose readings that are too precise, while an implementation that only rounds readings up may provide attackers with information about more precise readings when raw readings are rounded to different values.

Note: Inaccuracies will further increase for operations carried out on the sensor readings , or time deltas calculated from the timestamps . So, this mitigation strategy can affect certain use cases.

Note: while adding random bias to sensor readings has similar effects, it shouldn’t be used in practice as it is easy to filter out the added noise.

4.3.5. Keep the user informed about API use

User agents may choose to keep the user informed about current and past use of the API.

Note: this does not imply keeping a log of the actual sensor readings which would have issues of its own.

5. Concepts

5.1. Sensors

The term device sensor refers to a device’s underlying physical sensor instance.

A device sensor measures a physical quantities and provides a corresponding sensor reading which is a source of information about the environment.

Each sensor reading is composed of the values of the physical quantity measured by the device sensor at time t _n which is called the reading timestamp .

If the device sensor performs a spatial measurement (e.g. acceleration, angular velocity), it must be resolved in a local coordinate system that represents a reference frame for the device sensor 's sensor readings . A device sensor that provides such sensor readings is referred to as spatial sensor .

A spatial sensor can be uniaxial , biaxial , or triaxial , depending on the number of orthogonal axes in which it can perform simultaneous measurements.

Scalar physical quantities (e.g. temperature) do not require a local coordinate system for resolution.

The local coordinate system normally used in a mobile device is a Cartesian coordinate system, which is defined relative to the device’s screen, so that X and Y axes are parallel to the screen dimentions and Z axis is perpendicular to the screen surface.

The term platform sensor refers to platform interfaces, with which the user agent interacts to obtain sensor readings for a single sensor type originated from one or more device sensors .

Platform sensor can be defined by the underlying platform (e.g. in a native sensors framework) or by the user agent, if it has a direct access to device sensor .

From the implementation perspective platform sensor can be treated as a software proxy for the corresponding device sensor . It is possible to have multiple platform sensors simultaneously interacting with the same device sensor if the underlying platform suppports it.

In simple cases, a platform sensor corresponds to a single device sensor , but if the provided sensor readings are a product of sensor fusion performed in software, the platform sensor corresponds to a set of device sensors involved in the sensor fusion process.

Discrepancies between a sensor reading and the corresponding physical quantity being measured are corrected through calibration that can happen at manufacturing time. Some sensors can require dynamic calibration to compensate unknown discrepancies.

Note: platform sensors created through sensor fusion are sometimes called virtual or synthetic sensors. However, the specification doesn’t make any practical distinction between them.

5.2. Sensor Types

Different sensor types measure different physical quantities such as temperature, air pressure, heart-rate, or luminosity.

For the purpose of this specification we distinguish between high-level and low-level sensor types .

Sensor types which are characterized by their implementation are referred to as low-level sensors. For example a Gyroscope is a low-level sensor type .

Sensors named after their readings , regardless of the implementation, are said to be high-level sensors. For instance, geolocation sensors provide information about the user’s location, but the precise means by which this data is obtained is purposefully left opaque (it could come from a GPS chip, network cell triangulation, wifi networks, etc. or any combination of the above) and depends on various, implementation-specific heuristics. High-level sensors are generally the fruits of applying algorithms to low-level sensors— for example, a pedometer can be built using only the output of a gyroscope— or of sensor fusion .

That said, the distinction between high-level and low-level sensor types is somewhat arbitrary and the line between the two is often blurred. For instance, a barometer, which measures air pressure, would be considered low-level for most common purposes, even though it is the product of the sensor fusion of resistive piezo-electric pressure and temperature sensors. Exposing the sensors that compose it would serve no practical purpose; who cares about the temperature of a piezo-electric sensor? A pressure-altimeter would probably fall in the same category, while a nondescript altimeter— which could get its data from either a barometer or a GPS signal— would clearly be categorized as a high-level sensor type .

Because the distinction is somewhat blurry, extensions to this specification (see § 10 Extensibility ) are encouraged to provide domain-specific definitions of high-level and low-level sensors for the given sensor types they are targeting.

Sensor readings from different sensor types can be combined together through a process called sensor fusion . This process provides higher-level or more accurate data (often at the cost of increased latency). For example, the readings of a triaxial magnetometer needs to be combined with the readings of an accelerometer to provide a correct bearing.

Smart sensors and sensor hubs have built-in compute resources which allow them to carry out calibration and sensor fusion at the hardware level, freeing up CPU resources and lowering battery consumption in the process.

Sensor fusion can also be carried out in software if it cannot be performed at the hardware level or if an application-specific fusion algorithm is required.

5.3. Default sensor

The Generic Sensor API is designed to make the most common use cases straightforward while still enabling more complex use cases.

Most of devices deployed today do not carry more than one device sensor providing sensor readings of the same type . The use cases which require a set of similar device sensors are rare and generally limited to specific sensor types , such as multiple accelerometers in 2-in-1 laptops.

The API therefore makes it easy to interact with the device’s default (and often unique) sensor for each type simply by instantiating the corresponding Sensor subclass.

Indeed, without specific information identifying a particular sensor of a given type , the default sensor is chosen by the user agent.

If the underlying platform provides an interface to find the default sensor , the user agent must choose the sensor offered by the platform, otherwise the user agent itself defines which of the sensors present on the device is the default sensor .

let sensor = new Accelerometer({ frequency: 30 });
sensor.onreading = () => { ... }
sensor.start();

Note: extension to this specification may choose not to define a default sensor when doing so wouldn’t make sense. For example, it does not make sense to explicitly define a default sensor for geolocation sensor type as the implementation of its interface can use multiple backends.

In cases where multiple device sensors corresponding to the same type may coexist on the same device, specification extension will have to define ways to uniquely identify each one.

var sensor = new DirectTirePressureSensor({ position: "rear", side: "left" });
sensor.onreading = _ => console.log(sensor.pressure);
sensor.start();

5.4. Sampling Frequency and Reporting Frequency

For the purpose of this specification, sampling frequency for a platform sensor is defined as a frequency at which the user agent obtains sensor readings from the underlying platform.

The user agent can request the underlying platform to deliver readings at a certain rate which is called requested sampling frequency .

The sampling frequency is equal to the requested sampling frequency if the underlying platform can support it.

The sampling frequency differs from the requested sampling frequency in the following cases:

• the requested sampling frequency exceeds upper or lower sampling frequency bounds supported by the underlying platform.

• the operating system and/or the device sensor automatically discard readings that do not differ enough (in absolute or relative terms) from the previously reported ones via a hardware or operating system filter.

• the platform sensor 's associated sensor type 's threshold check algorithm fails and the platform sensor 's latest readings are not updated.

The reporting frequency for a concrete Sensor object is defined as a frequency at which the "reading" event is fired at this object.

A Sensor object cannot access new readings at a higher rate than the user agent obtains them from the underlying platform, therefore the reporting frequency can never exceed the sampling frequency for the given sensor type .

5.5. Conditions to expose sensor readings

The user agent can expose sensor readings to a given document if and only if all of the following are true:

• document ’s relevant settings object is a secure context .

• document ’s visibility state is "visible".

• The currently focused area belongs to a document whose origin is same origin-domain with document ’s origin.

• Specific conditions : Extension specifications may add new conditions to this list to have stricter requirements for their sensor types.

Note: In addition to the conditions above, it is important to note that Sensor subclasses invoke the check sensor policy-controlled features operation in their constructors, and § 7.1.7 Sensor.start() invokes request sensor access . Together, these checks correspond to the mitigation strategies described in § 4.2 Mitigation Strategies .

Note: In order to release hardware resources, the user agent can request underlying platform sensor to suspend notifications about newly available readings until it can expose sensor readings .

6. Model

6.1. Sensor Type

A sensor type has one or more associated extension sensor interfaces .

A sensor type has a set of associated sensors .

A sensor type may have a default sensor .

A sensor type has a nonempty set of associated names referred to as sensor permission names .

Note: multiple sensor types may share the same name . In specific cases, extension specifications might choose to define an empty set of sensor permission names if their permission model is integrated with that of another specification.

A sensor type has a permission revocation algorithm .

A sensor type has a permission request algorithm .

A sensor type has a nonempty set of associated policy-controlled feature tokens referred to as sensor feature names .

A sensor type may have an associated threshold check algorithm , which takes as arguments two separate sensor readings and determines if they differ enough to cause a platform sensor 's latest reading map to be updated.

A sensor type may have an associated reading quantization algorithm , which takes a sensor reading and returns a less accurate sensor reading .

A sensor type may have an associated pre-activation checks algorithm , which takes a Sensor instance and returns a boolean, to perform extra checks before activating the given Sensor instance.

6.2. Sensor

The current browsing context 's platform sensor must have:

• An associated set of activated sensor objects , which is initially empty ;

• An associated latest reading map , which holds the latest available sensor readings .

• An associated sensor type .

Note: User agents can share the latest reading map and the activated sensor objects set between different contexts only if the origins of these contexts' active documents are same origin-domain .

Any time a new sensor reading for a platform sensor is obtained and if the user agent can expose sensor readings to the current browsing context 's active document , the user agent invokes update latest reading with the platform sensor and the sensor reading as arguments.

The latest reading map contains an entry whose key is "timestamp" and whose value is a high resolution timestamp that estimates the reading timestamp expressed in milliseconds since the time origin .

Note: The accuracy of the reading timestamp estimate depends on the underlying platform interfaces that expose it.

The latest reading ["timestamp"] is initially set to null, unless the latest reading map caches a previous reading .

The other entries of the latest reading map hold the values of the different quantities measured by the platform sensor . The keys of these entries must match the attribute identifier defined by the sensor type 's associated extension sensor interface . The return value of the attribute getter is easily obtained by invoking get value from latest reading with the object implementing the extension sensor interface and the attribute identifier as arguments.

The value of all latest reading entries is initially set to null.

A platform sensor has an associated requested sampling frequency which is initially null.

For a non- empty set of activated sensor objects the requested sampling frequency is equal to the optimal sampling frequency , which is estimated by the user agent by taking into account the provided frequencies of activated Sensors and the sampling frequency bounds defined by the underlying platform.

Note: For example, the user agent may estimate optimal sampling frequency as a Least Common Denominator (LCD) for a set of provided frequencies capped by sampling frequency bounds defined by the underlying platform.

7. API

7.1. The Sensor Interface

[SecureContext, Exposed=(DedicatedWorker, Window)]
interface Sensor : EventTarget {
  readonly attribute boolean activated;
  readonly attribute boolean hasReading;
  readonly attribute DOMHighResTimeStamp? timestamp;
  undefined start();
  undefined stop();
  attribute EventHandler onreading;
  attribute EventHandler onactivate;
  attribute EventHandler onerror;
};
dictionary SensorOptions {
  double frequency;
};

A Sensor object has an associated platform sensor .

The task source for the tasks mentioned in this specification is the sensor task source .

navigator.permissions.query({ name: 'accelerometer' }).then(result => {
    if (result.state === 'denied') {
        console.log('Permission to use accelerometer sensor is denied.');
        return;
    }
    let acl = new Accelerometer({frequency: 30});
    let max_magnitude = 0;
    acl.addEventListener('activate', () => console.log('Ready to measure.'));
    acl.addEventListener('error', error => console.log(`Error: ${error.name}`));
    acl.addEventListener('reading', () => {
        let magnitude = Math.hypot(acl.x, acl.y, acl.z);
        if (magnitude > max_magnitude) {
            max_magnitude = magnitude;
            console.log(`Max magnitude: ${max_magnitude} m/s2`);
        }
    });
    acl.start();
});

7.1.1. Sensor lifecycle

Note: the nodes in the diagram above represent the states of a Sensor object and they should not be confused with the possible states of the underlying platform sensor or device sensor .

7.1.2. Sensor garbage collection

A Sensor object whose [[state]] is "activating" must not be garbage collected if there are any event listeners registered for "activated" events, "reading" events, or "error" events.

A Sensor object whose [[state]] is "activated" must not be garbage collected if there are any event listeners registered for "reading" events, or "error" events.

When a Sensor object whose [[state]] is "activated" or "activating" is garbage collected, the user agent must invoke deactivate a sensor object with this object as argument.

7.1.3. Sensor internal slots

Instances of Sensor are created with the internal slots described in the following table:

7.1.4. Sensor.activated

7.1.5. Sensor.hasReading

7.1.6. Sensor.timestamp

The timestamp getter steps are to return the result of invoking get value from latest reading with this and "timestamp" as arguments.

It represents a reading timestamp .

7.1.7. Sensor.start()

7.1.8. Sensor.stop()

7.1.9. Sensor.onreading

onreading is an EventHandler which is called to notify that new reading is available.

7.1.10. Sensor.onactivate

onactivate is an EventHandler which is called when this . [[state]] transitions from "activating" to "activated".

7.1.11. Sensor.onerror

onerror is an EventHandler which is called whenever an exception cannot be handled synchronously.

7.1.12. Event handlers

The following are the event handlers (and their corresponding event handler event types ) that must be supported as attributes by the objects implementing the Sensor interface:

7.2. The SensorErrorEvent Interface

[SecureContext, Exposed=(DedicatedWorker, Window)]
interface SensorErrorEvent : Event {
  constructor(DOMString type, SensorErrorEventInit errorEventInitDict);
  readonly attribute DOMException error;
};
dictionary SensorErrorEventInit : EventInit {
  required DOMException error;
};

SensorErrorEvent instances are constructed by following the steps described in Event 's constructor .

The error attribute must return the value it was initialized to. It represents the DOMException object passed to SensorErrorEventInit .

8. Abstract Operations

8.1. Initialize a sensor object

8.2. Check sensor policy-controlled features

8.3. Connect to sensor

8.4. Activate a sensor object

8.5. Deactivate a sensor object

8.6. Revoke sensor permission

8.7. Set sensor settings

8.8. Update latest reading

8.9. Find the reporting frequency of a sensor object

8.10. Report latest reading updated

8.11. Notify new reading

8.12. Notify activated state

8.13. Notify error

8.14. Get value from latest reading

8.15. Request sensor access

9. Automation

The Generic Sensor API and its extension specifications pose a challenge to test authors, as fully exercising those interfaces requires physical hardware devices that respond in predictable ways. To address this challenge this document defines a number of extension commands to the [WEBDRIVER2] specification for controlling mock sensor on the host that the user agent is running on. With these extension commands , devices with particular properties can be created and their responses to requests are well defined.

9.1. Mock Sensors

A mock sensor simulates the behavior of a platform sensor in controlled ways.

A mock sensor reports a corresponding mock sensor reading , which is a source of mocking information about the environment, to the Sensor objects.

The current browsing context 's mock sensor has an associated mock sensor reading map .

The mock sensor reading map contains an entry whose key is "timestamp" and whose value is a high resolution timestamp that estimates the time mock sensor reading sent to observers of the Sensor object, expressed in milliseconds since the time origin .

The other entries of the mock sensor reading map whose keys must match the dictionary members identifier defined by the mock sensor type 's MockSensorReadingValues and whose initial values are implementation-dependent.

Note: The user agent must provide the mock sensor reading that are initially exposed to the Sensor objects.

A mock sensor has an associated requested sampling frequency . Its default value is implementation-dependent but must be set within a mock sensor 's associated sampling frequency bounds.

A mock sensor has an associated sampling frequency with supported bounds. The default values of supported bounds are implementation-dependent.

A mock sensor must report the mock sensor reading at the rate of its requested sampling frequency if the user agent can expose sensor readings to the current browsing context 's active document .

Note: The mock sensor defined in this specification is not intended be used by non-testing-related web content. The UA MAY choose to expose mock sensor interface only when a runtime or compile-time flag has been set.

9.1.1. MockSensorConfiguration dictionary

dictionary MockSensorConfiguration {
  required MockSensorType mockSensorType;
  boolean connected = true;
  double? maxSamplingFrequency;
  double? minSamplingFrequency;
};

The MockSensorConfiguration dictionary is used to create a mock sensor .

mockSensorType member

A MockSensorType that is used to set mock sensor type .

connected member

A boolean that indicates a mock sensor 's connection flag which is used for switching the connection between Sensor object and mock sensor . When set to false the user agent must force the result of invoking connect to sensor with mock sensor 's associated Sensor object as argument to false, otherwise true.

maxSamplingFrequency member

A double representing frequency in Hz that is used to set maximum supported sampling frequency for the associated mock sensor .

minSamplingFrequency member

A double representing frequency in Hz that is used to set minimum supported sampling frequency for the associated mock sensor .

9.1.2. MockSensor dictionary

dictionary MockSensor {
  double maxSamplingFrequency;
  double minSamplingFrequency;
  double requestedSamplingFrequency;
};

The MockSensor dictionary provides information about a mock sensor .

maxSamplingFrequency member

A double representing frequency in Hz that indicates the maximum supported sampling frequency of the associated mock sensor .

minSamplingFrequency member

A double representing frequency in Hz that indicates the minimum supported sampling frequency of the associated mock sensor .

requestedSamplingFrequency member

A double representing frequency in Hz that indicates the requested sampling frequency of the associated mock sensor .

A serialized mock sensor is a JSON Object where a mock sensor 's fields listed in the MockSensor dictionary are mapped using the JSON Key and the associated field’s value from the available mock sensor in current browsing context .

9.1.3. Mock sensor type

A mock sensor type is equivalent to a sensor type 's associated Sensor subclass.

enum MockSensorType {
  "ambient-light",
  "accelerometer",
  "linear-acceleration",
  "gravity",
  "gyroscope",
  "magnetometer",
  "uncalibrated-magnetometer",
  "absolute-orientation",
  "relative-orientation",
  "geolocation",
  "proximity",
};

Each enumeration value in the MockSensorType enum identifies a mock sensor type .

"ambient-light"

A mock sensor type associated with the usage of the AmbientLightSensor interface.

"accelerometer"

A mock sensor type associated with the usage of the Accelerometer interface.

"linear-acceleration"

A mock sensor type associated with the usage of the LinearAccelerationSensor interface.

"gravity"

A mock sensor type associated with the usage of the GravitySensor interface.

"gyroscope"

A mock sensor type associated with the usage of the Gyroscope interface.

"magnetometer"

A mock sensor type associated with the usage of the Magnetometer interface.

"uncalibrated-magnetometer"

A mock sensor type associated with the usage of the UncalibratedMagnetometer interface.

"absolute-orientation"

A mock sensor type associated with the usage of the AbsoluteOrientationSensor interface.

"relative-orientation"

A mock sensor type associated with the usage of the RelativeOrientationSensor interface.

"geolocation"

A mock sensor type associated with the usage of the GeolocationSensor interface.

"proximity"

A mock sensor type associated with the usage of the ProximitySensor interface.

Each mock sensor type has a mock sensor reading values dictionary:

Mock Sensor Reading Values dictionary

MockSensorReadingValues dictionary represents a user-specified mock sensor reading used for updating a mock sensor reading . Its members must match the attribute identifier defined by the sensor type 's associated extension sensor interface . Each mock sensor type has a specific MockSensorReadingValues , which is defined in each extension specifications .

dictionary MockSensorReadingValues {
};

9.2. Extension Commands

9.2.1. Create mock sensor

{
  "mockSensorType": "ambient-light",
  "maxSamplingFrequency": 60,
  "minSamplingFrequency": 5
}

9.2.2. Get mock sensor

9.2.3. Update mock sensor reading

9.2.4. Delete mock sensor

9.3. Handling errors

This section extends the WebDriver § 6.6 Errors section and defines extended WebDriver error codes specific for mock sensor in following table.

10. Extensibility

This section is non-normative.

Note: This section and its subsections provide guidance to extension specification authors using normative language. From implementers' point of view, this section and its subsections are considered non-normative.

This section describes how this specification can be extended to specify APIs for different sensor types .

Such extension specifications are encouraged to focus on a single sensor type , exposing both high and low level as appropriate.

Extension specifications are encouraged to define whether a calibration process applies to sensor readings .

Extension specifications may explicitly define the local coordinate system for the associated sensor type or make it configurable per Sensor object.

For an up-to-date list of extension specifications , please refer to [GENERIC-SENSOR-USECASES] and [MOTION-SENSORS] documents.

10.1. Security and Privacy

Extension specifications are expected to:

• conform with the generic mitigation strategies ,

• consider mitigation strategies applied on a case by case basis ,

• be evaluated against the Self-Review Questionnaire on Security and Privacy [SECURITY-PRIVACY-QUESTIONNAIRE] ,

• and in particular, be evaluated against the same-origin policy violations that can arise if sensors expose a new communication channel not governed by the same-origin policy.

10.2. Naming

Sensor interfaces for low-level sensors should be named after their associated platform sensor . So for example, the interface associated with a gyroscope should be simply named Gyroscope . Sensor interfaces for high-level sensors should be named by combining the physical quantity the platform sensor measures with the "Sensor" suffix. For example, a platform sensor measuring the distance at which an object is from it may see its associated interface called ProximitySensor .

Attributes of the Sensor subclass that hold sensor readings values should be named after the full name of these values. For example, the Thermometer interface should hold the sensor reading 's value in a temperature attribute (and not a value or temp attribute). A good starting point for naming are the Quantities, Units, Dimensions and Data Types Ontologies [QUDT] .

10.3. Unit

Extension specifications must specify the unit of sensor readings .

As per the Technical Architecture Group’s (TAG) API Design Principles [API-DESIGN-PRINCIPLES] , all time measurement should be in milliseconds. All other units should be specified using, in order of preference, and with the exception of temperature (for which Celsius should be favored over Kelvin), the International System of Units (SI), SI derived units, and Non-SI units accepted for use with the SI, as described in the SI Brochure [SI] .

10.4. Exposing High-Level vs. Low-Level Sensors

So far, specifications exposing sensors to the Web platform have focused on high-level sensors APIs. [GEOLOCATION-API] [ORIENTATION-EVENT]

This was a reasonable approach for a number of reasons. Indeed, high-level sensors:

• convey developer intent clearly,

• do not require intimate knowledge of how the underlying hardware sensors functions,

• are easy to use,

• may enable the User Agent to make significant performance and battery life improvements,

• help avoid certain privacy and security issues by decreasing the amount and type of information exposed.

However, an increasing number of use cases such as virtual and augmented reality require low-level access to sensors, most notably for performance reasons.

Providing low-level access enables Web application developers to leverage domain-specific constraints and design more performant systems.

Following the precepts of the Extensible Web Manifesto [EXTENNNNSIBLE] , extension specifications should focus primarily on exposing low-level sensor APIs, but should also expose high-level APIs when they are clear benefits in doing so.

10.5. When is Enabling Multiple Sensors of the Same Type Not the Right Choice?

It is not advisable to construct multiple Sensor instances of the same sensor type with equal construction parameters, as it can lead to unnecessary hardware resources consumption.

In cases when multiple observers are interested in notifications of a newly available sensor reading , an event listener can be added on a single Sensor instance instead of creating multiple instances of the same sensor type and using simple onreading event handler.

Conversely, multiple Sensors of the same sensor type can be created when they are intended to be used with different settings, such as: requested sampling frequency , accuracy or other settings defined in extension specifications .

10.6. Definition Requirements

The following definitions must be specified for each sensor type in extension specifications :

• An extension sensor interface , which is an interface whose inherited interfaces contains Sensor . The extension sensor interface must be constructible. Its [ Constructor ] must take, as an argument, an optional dictionary whose inherited dictionaries contains SensorOptions .

  The extension sensor interface has a set of supported options referred to as supported sensor options . Unless the extension specification defines otherwise, supported sensor options contain a single item which is "frequency".

  The user agent must remove items from supported sensor options for a given extension sensor interface if it cannot support the corresponding sensor options.

  The extension sensor interface attributes which expose sensor readings are read only and their getters must return the result of invoking get value from latest reading with this and attribute identifier as arguments.

• A name , if the sensor type is not representing sensor fusion (otherwise, names associated with the fusion source sensor types must be used).

An extension specification may specify the following definitions for each sensor types :

• A dictionary whose inherited dictionaries contains SensorOptions .

• A default sensor . Generally, devices are equipped with a single platform sensor of each type , so defining a default sensor should be straightforward. For sensor types where multiple sensors are common, extension specifications may choose not to define a default sensor , especially when doing so would not make sense.

• A threshold check algorithm , which returns a boolean indicating whether two sensor readings differ enough to cause the latest readings map to be updated.

• A reading quantization algorithm , which may return a sensor reading with reduced accuracy.

• A pre-activation checks algorithm with extra steps that are run before a Sensor instance is activated.

10.7. Automation

In order to enable user-agent automation and application testing, extension specifications are encouraged to:

• Add new mock sensor type for each extension sensor interface to the MockSensorType enum.

• Define a mock sensor reading values dictionary.

10.8. Extending the Permission API

An implementation of the Sensor interface for each sensor type must protect its reading by associated name or PermissionDescriptor . A low-level sensor may use its interface name as a name , for instance, "gyroscope" or "accelerometer". Fusion sensors must request permission to access each of the sensors that are used as a source of fusion.

Note: see the note in § 4.2.5 Permissions API . In specific cases such as [AMBIENT-LIGHT] , an extension specification may choose to rely on names defined in another specification rather than specifying their own sensor permission names .

Even though it might be difficult to reconstruct low-level sensor readings from fused data, some of the original information might be inferred. For example, it is easy to deduce user’s orientation in space if absolute or geomagnetic orientation sensors are used, therefore, these sensors must request permission to use magnetometer as it provides information about orientation of device in relation to Earth’s magnetic field. In contrast, relative orientation sensor does not expose such information, thus, it does not need to request permission to use magnetometer.

Permission descriptors can also be used to set maximum allowed limits for accuracy or sampling frequency . An example for a possible extension of the Permission API for accelerometer sensor is given below.

dictionary AccelerometerPermissionDescriptor : PermissionDescriptor {
    boolean highAccuracy = false;
    boolean highFrequency = false;
};

10.9. Extending the Permissions Policy API

An implementation of the Sensor interface for each sensor type has one (if sensor fusion is not performed) or several policy-controlled features that control whether or not this implementation can be used in a document.

The features ' default allowlist is 'self' .

Note: The default allowlist of 'self' allows Sensor interface implementation usage in same-origin nested frames but prevents third-party content from sensor readings access.

The sensor feature names set must contain policy-controlled feature tokens of every associated feature .

A low-level sensor may use its interface name as a policy-controlled feature token, for instance, "gyroscope" or "accelerometer". Unless the extension specification defines otherwise, the sensor feature names matches the same type -associated sensor permission names .

<iframe src="https://third-party.com" allow="accelerometer"/></iframe>

Permissions-Policy: accelerometer=()

Fusion sensors must use sensor feature names of the sensors that are used as a source of fusion.

<iframe src="https://third-party.com" allow="accelerometer; magnetometer; gyroscope"/>

10.10. Example WebIDL

Here’s an example WebIDL for a possible extension of this specification for proximity sensors .

[SecureContext, Exposed=Window]
interface ProximitySensor : Sensor {
    constructor(optional ProximitySensorOptions proximitySensorOptions = {});
    readonly attribute double? distance;
};
dictionary ProximitySensorOptions : SensorOptions {
    double min;
    double max;
    ProximitySensorPosition position;
    ProximitySensorDirection direction;
};
enum ProximitySensorPosition {
    "top-left",
    "top",
    "top-right",
    "middle-left",
    "middle",
    "middle-right",
    "bottom-left",
    "bottom",
    "bottom-right"
};
enum ProximitySensorDirection {
    "front",
    "rear",
    "left",
    "right",
    "top",
    "bottom"
};

11. Acknowledgements

First and foremost, I would like to thank Anssi Kostiainen for his continuous and dedicated support and input throughout the development of this specification, as well as Mikhail Pozdnyakov, Alexander Shalamov, Rijubrata Bhaumik, and Kenneth Rohde Christiansen for their invaluable implementation feedback, suggestions, and research that have helped inform the specification work.

Special thanks to Rick Waldron for driving the discussion around a generic sensor API design for the Web, sketching the original API on which this is based, providing implementation feedback from his work on Johnny-Five, and continuous input during the development of this specification.

Special thanks to Boris Smus, Tim Volodine, and Rich Tibbett for their initial work on exposing sensors to the web with consistency.

Thanks to Anne van Kesteren for his tireless help both in person and through IRC.

Thanks to Domenic Denicola and Jake Archibald for their help.

Thanks also to Frederick Hirsch and Dominique Hazaël-Massieux (via the HTML5Apps project) for both their administrative help and technical input.

Thanks to Tab Atkins for making Bikeshed and taking the time to explain its subtleties.

Thanks to Lukasz Olejnik and Maryam Mehrnezhad for their contributions around privacy and security.

The following people have greatly contributed to this specification through extensive discussions on GitHub: Anssi Kostiainen, Boris Smus, chaals, Claes Nilsson, Dave Raggett, David Mark Clements, Domenic Denicola, Dominique Hazaël-Massieux (via the HTML5Apps project), Francesco Iovine, Frederick Hirsch, gmandyam, Jafar Husain, Johannes Hund, Kris Kowal, Lukasz Olejnik, Marcos Caceres, Marijn Kruisselbrink, Mark Foltz, Mats Wichmann, Matthew Podwysocki, Olli Pettay, pablochacin, Remy Sharp, Rich Tibbett, Rick Waldron, Rijubrata Bhaumik, robman, Sean T. McBeth, Tab Atkins Jr., Virginie Galindo, zenparsing, and Zoltan Kis.

We’d also like to thank Anssi Kostiainen, Dominique Hazaël-Massieux, Erik Wilde, and Michael[tm] Smith for their editorial input.

Conformance

Document conventions

Conformance requirements are expressed with a combination of descriptive assertions and RFC 2119 terminology. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in the normative parts of this document are to be interpreted as described in RFC 2119. However, for readability, these words do not appear in all uppercase letters in this specification.

All of the text of this specification is normative except sections explicitly marked as non-normative, examples, and notes. [RFC2119]

Examples in this specification are introduced with the words "for example" or are set apart from the normative text with class="example" , like this:

Because this document doesn’t itself define APIs for specific sensor types — that is the role of extensions to this specification— all examples are inevitably (wishful) fabrications. Although all of the sensors used a examples would be great candidates for building atop the Generic Sensor API, their inclusion in this document does not imply that the relevant Working Groups are planning to do so.

Informative notes begin with the word "Note" and are set apart from the normative text with class="note" , like this:

Note, this is an informative note.

Conformant Algorithms

Requirements phrased in the imperative as part of algorithms (such as "strip any leading space characters" or "return false") are to be interpreted with the meaning of the key word ("must", "should", "may", etc) used in introducing the algorithm.

Conformance requirements phrased as algorithms or specific steps can be implemented in any manner, so long as the end result is equivalent . In particular, the algorithms defined in this specification are intended to be easy to understand and are not intended to be performant. Implementers are encouraged to optimize.

Conformance Classes

A conformant user agent must implement all the requirements listed in this specification that are applicable to user agents.